Barnett Machine Tools, Inc.

Specifications:
Tonnage Capacity: 1500 tons
Overall Length of Bed & Ram: 23’
Distance Between Housings: 20’2”
Bending Capacity: 1”x18’ depending on Die
Stroke Length:18”
Open Height: 30”
Closed Height: 12”
Throat Depth: 20”
Ram Speeds:
Rapid Advance: 56 IPM
Fast Press: 29 IPM
Normal Press: 9 IPM
Normal Return: 21 IPM
Rapid Return: 65 IPM
Motor: 60 HP
Electrics: 3 Phase 60 Cycle

Equipped With:
Adjustable Stroke
Tonnage Control
Level Control System
Pacific Universal Gauges
Bed & Ram Machined & Drilled for Angle Plates
Oil Cooling Unit
New Electrical Controls in 2005
Dual Foot Switches
Dual Palm Button Stands
Light Curtains
New Manuals

SPECIFICATIONS
Capacity: 400 tons
Overall Length of Bed: 14’
Distance Between Housing: 12’ 4 1/2”
Stroke Length: 12”
Open Height: 20”
Closed Height: 8”
Throat Depth: 10”
Ram Speeds: 3 Speeds
57” IPM Rapid Advance
25” IPM Normal Press
55” IPM Return Press
Motor: 40 HP
Electronics: 220/440 Volt; 60 Cycle; 3 Phase

EQUIPPED WITH
Stroke Control
Hydraulic Level Control
Bed and Ram Machined and Drilled for Angle Plates
Upper Section Ram Clamps
Full Set of Angle Plates

*Note: This machine requires a pit at least 35” deep x 137” long x 3-1/2”
wide.

SPECIFICATIONS
Capacity at 90 deg Rectangular: 25” x 36”
Round: 25”
Capacity at 45 deg Rectangular: 25” x 20”
Round: 20”
Weight Capacity: 15,000 lbs.
Blade Size: 1-1/4” x .042” x 22’6”
Bandwheel Size: 26” diameter
Blade Speed: 70 – 475 SFPM
Sawing Force: 0 – 300 lbs.
Infeed Table w/Hydraulic Vise: 16’
Work Height: 27”
Blade Drive: 5 HP
Hydraulic Drive: 2 HP
Coolant Capacity: 15 gallons
Hydraulic Capacity: 20 gallons
Overall Dimensions(approx): 135” x 44” x 98”H
Weight (approx): 4,700 lbs.

EQUIPPED WITH
Automatic Feed
Multiple Stroke (3)
Spring Loaded Carbide Guides
Hydraulic Vise Operation
Hydraulic Blade Tension
Preset Counter
Adjustable Cutting Force
Built-In Coolant System
45 Degree Swiveling Vise
Powered Blade Brush
Fused Disconnect w/Lockout
Console Controlled Blade Speed
Feed Pressure Monitor/Regulator
Auto Shutoff/Blade Breakage
Motor & Electrical Controls

SPECIFICATIONS
Capacity: 10 GA
Max Cutting Length: 10’
Rake of Upper Blade: 3/8”
Number of Holddowns: 16
Backgauge Range: 36”
Strokes Per Min: 60
Dimensions: 14’ x 6’ x 5’
Weight (approx): 13,500 lbs.

SPECIFICATIONS
Tonnage Capacity: 1000 tons
Overall Length of Bed & Ram: 20’ includes a 4’ horn on each side of ram.

*Machine was originally 12’ overall bed & ram length.
Distance Between Housings: 10’2”
Throat Depth: 16”
Stroke Length: 18”
Open Height: 30”
Closed Height: 12”
Rapid Advance: 9 IPM
Normal Press: 17 IPM
Fast Press: 50 IPM
Normal Return: 48 IPM
Fast Return: 132 IPM

EQUIPPED WITH
Adjustable Stroke Control
Hydraulic Tonnage Control
Level Control System
Electric Foot Switch
10 Micron Filter System

SPECIFICATIONS:
Tonnage Capacity: 750 tons
Overall Length of Bed & Ram: 22’
Distance Between Housings: 18’2”
Bending Capacity: 5/8” x 20’
Throat Depth: 14”
Stroke Length: 12”
Open Height: 22”
Closed Height: 10”
Rapid Advance: 90 IPM
Normal Press: 17 IPM
Fast Press: 50 IPM
Normal Return: 48 IPM
Fast Return: 132 IPM
Motor: 60 HP
Weight (approx): 125,000 lbs.

EQUIPPED WITH:
T-Slotted Bed
2’ Horn on Left Side of Ram
3 Speed Hydraulic Power Unit
Electric Foot Switch Controls
Large Quantity of Tooling

Specifications
Capacity: 300 Tons
Stroke: 8”
Shut Height: 22”
Slide Adjustment: 6”
Bed & Slide Area: 102”LR x 48”FB
Speed: 30 Strokes Per Minute
Windows: 26.75”

Floor Space: 120”LR x 75”FB
Height: 171”
Weight: 38,000# without bolster plate

Equipped With
Air Clutch & Brake
Air Counterbalance
Bolster Plate
Electrics & Controls
30 HP Drive Motor
Flush Floor Design

SPECIFICATIONS
Capacity: 175 tons
14’ of 3/16” material
10’ of 1/4” material
6’ of 3/8” material
Length of Bed & Ram: 14’
Distance Between Side Housings: 12’6”
Ram Stroke: 0-10”
Open Height: 17”
Closed Height: 7”
Ram Speeds
Rapid Advance: 115
Standard High Speed: 272
Normal Press: 58
Anti Back Bend: 13
Rapid Return: 115
Throat Depth: 8”
Main Motor: 30 HP
Electrics: 220/440 V 3 PH 60 Cycle

EQUIPPED WITH
Tonnage Control Valve w/Gauge
3 Speed Ram Control
Micro Ram Tilt
Electric Foot Switch Control
4 Way Die & Misc. Brake Tooling
Flush Floor Machine
Hydraulic Fluid Cooling Unit

SPECIFICATIONS
Working Length of Rolls: 4580mm (180.3”)
Max. Width of Plate: 4500mm (177.2”)
Upper Roll Diameter: 1100mm (43.3”)
Lower Roll Diameter: 650mm (25.6”)
Distance Between Lower Rolls: 950mm (37.4”)
Max. Distance Between Upper &
Lower Rolls: 270mm (10.6”)
Down Travel of Upper Roll: 400mm (15.7”)
Horizontal Travel of Lower Rolls
To Both Sides from Middle Position: 300mm (11.8”)
Plate Feeds: m/1’; 2.2 - 3.3 - 5.
Up & Down Speed of Upper Roll: 3 – 4.5mm / sec
Speed of Lower Rolls: 4 – 5.7mm / sec
Vertical Force on Upper Rolls: 2700 ton
Vertical Force on Lower Rolls:1800 ton
Allowed Angle for Upper Roll: 3 degree 30”
Total Power: 605 HP
Weight (est.): 330 ton

SPECIFICATIONS
Capacity: 3/4” x 12’
Full Rake: 1” x 12’
Distance Between Housings: 12’3”
Throat Depth: 18”
Overall Bed Length: 12’
Table Height from Floor: 43”

EQUIPPED WITH
2 Front Operated Support Arms Rake Control
Ball Transfers in Table Inch, Single Stroke
Front Operated Backgauge Backgauge Swing Up Feature
Nitrogen Pull Backs Hyd. Blade Clearance Adjustment

SPECIFICATIONS
Capacity: 1/2” x 12’
Full Rake: 3/4” x 12’
Distance Between Housings: 12’3”
Throat Depth: 18”
Knife Open Height: 1-1/4”
Rake: 5/8”/ft. max.

EQUIPPED WITH
Ball Transfers in Table Inch, Single Stroke
Front Operated Power Backgauge Hydraulic Blade Clearance Adjust
Backgauge Swing Up Feature

EQUIPPED WITH:

36” Front Operated Backgauge

10’ Squaring Arm

Front Support Arms

Electrical Foot Switch

Air Actuated Clutch

Auto Lube System

SPECIFICATIONS

Capacity: 1/4”

Shearing Length: 120”

Distance Between Housings: 10’3”

Rake (IN/FT): 1/4”

Number of Holddowns: 11

Backgauge Range: 36”

Standard Max Strokes per Min: 60

Main Drive Motor: 7.5 HP

Backgauge Motor: .5 HP

Approx Weight: 18,000 lbs.

EQUIPPED WITH
36” Front Operated Power Backgauge

4’ Squaring Arm

Dovetail Slot Full Length of Bed

Variable Stroke Control

Auto Rake Angle & Blade Clearance

Electric Foot Switch
SPECIFICATIONS
Capacity A-36: 3/4”

Width: 10’

Nominal Rake: 1/2”

Max Rake: 3/4”

Number of Holddowns: 11

Holddown Tonnage: 89 tons

Blade Size: 1-1/8” x 5”

Approx Ram Speed IN/SEC

Down: .91

Up: 1.65

Cycles Full Width Cut: 5.2
Cycles Half Width Cut: 10.9

Motor: 50 HP

3 Phase 60 Cycle Electrics

EQUIPPED WITH:

Power Vise with Adjustable Pressure

Power Head Clamp

Power Blade Tension

Power Infeed & Retract

Air over Hydraulic Operation

45 Degree Tilt Either Direction

Coolant System

SPECIFICATIONS:

1-1/4” Bandsaw Blade for Straighter & Faster Cuts

18” Deep by 22” High Cutting Capacity – 90 Degrees

18” Deep by 22” High Cutting Capacity – 45 Degrees (left)

18” Deep by 15” High Cutting Capacity – 45 Degrees (right)

60 – 300 FPM Blade Speed

5 HP Variable Speed Blade Drive, Mounted on Top Bandwheel

440 Volt, 3 Phase

Dimensions: 5.6’ W x 9.6” L x 86” High

18.5” Diameter Band Wheels

26” x 26” Steel Table

34.5” Table Height

SPECIFICATIONS:

Copper Tubes (12 GA): 5

Copper Tubes (16 GA): 6

Standard St Pipe: 3-1/2

X Heavy Pipe: 3

XX Heavy Pipe: 2-1/2

Min Diameter: 24

Centers Lower Rolls: 18

Dia Angle Rolls: 16-1/2

RPM Rolls: 8

FPM: 35

Motor Size: 20 HP

Motor Speed: 1200 RPM

Variable Speed Drive

Dia Upper Shaft: 6

Dia Lower Shaft: 5

Gear Ratio: 150

Length: 10’6”

Width: 7’

Height: 5’4”

Weight: 13,000 lbs.

Angles Leg Out: 4 x 4 x 5/8

Min Diameter: 40

Angles Leg In: 3-1/2 x 3-1/2 x 5/8

Min Diameter: 48

Smallest Angle Leg Out: 1-1/2 x 1-1/2 x 1/4

Min Diameter: 18

Smallest Angle Leg In: 2 x 2 x 1/4

Min Diameter: 24

Beams on Flanges: 8” – 18”

Min Diameter: 60

Channels Flanges Out: 9”

Channels Flanges In: 7” – 14-3/4”

Min Diameter: 48

Flats on Edge: 4 x 1

Min Diameter: 48

Flats on Flat: 9 x 1-1/4

Min Diameter: 30

Rounds & Squares: 2-3/4 – 2-1/2

Min Diameter: 30

Specifications:

Tonnage Forming 150 ton

Tonnage Punching 100 ton

Bed Size 48 in. x 144 in.

Stroke 7 in

Die Height Open 14 in.

Die Height Closed 7 in.

Window Opening 24 in.

Inside Width 149 1/2 in.

Outside Width 168 in.

Bed Height 37 1/2 in.

Overall Height 123 in.

Approximate Weight 46,000 lbs.

Electrics 20 HP 220/440 3 Phase

SPECIFICATIONS

Capacity: 100 Tons

Bed & Ram: 36” x 111”

Daylight: 32”

Guide Posts: 3”

EQUIPPED WITH

Air Vacuum Tanks Electrical Controls

Front & Rear Palm Buttons

Motor Specifications:

Horse Power: 10

RPM: 1800

Voltage/Phase/Cy: 220/3/60

Model: T120HC209SSD268D276JA72IT106R*

*S/N: 18620 5209*

Specifications:

Capacity: 12 tons

Cycle Bore: 4.0

Stroke: 12

Daylight: 18 in.

Throat: 10 in.

Ram Diameter: 2.75 in.

Tank Capacity: 20 gal.

Max. PSI: 1910

Pump gpm: 9

Specifications

Serial Number: 14893 A81505 T1

Model Number: GC10C01A68D15

Capacity: 10 Tons

Drive Motor: 10 HP

Input Power: 220/440

Equipped With

Indexing Table with 6 Stations

Allen Bradley PLC Control

Specifications:

Maximum Weight: 1200 lbs.

Maximum Stock Width: 12 in.

Maximum Coil O.D.: 48 in.

Expansion Range: 10-22 in.

Maximum Speed (RPM): 0-23

Drive Motor: ¾ HP

Input Power: 120/1/60

Specifications:

Maximum Weight: 8000 lbs.

Maximum Stock Width: 18 in.

Maximum Coil O.D.: 60 in.

Expansion Range: 13-17 in.

Maximum Speed (FPM): 100

Specifications:

Stk. Width: 12 in.

Stk. Thickness in mild steel: 0.125 in.

Machine Direction: Left -> Right

Pass Line: 52.5 in.

Speed: 120-1200 IPM

Power Supply: 440/3 phase/60 HZ

Specifications:

Maximum Weight: 2500 lbs.

Maximum Coil O.D.: 50 in.

Maximum Speed (FPM): 30-65

Drive Motor: 1 HP

SPECIFICATIONS:

Table:16” x 78-1/2”

Taper: #50

Overarm Supports

SPECIFICATIONS:

X Axis Travel: 17.72”

Y Axis Travel: 12.55”

Z Axis Travel: 11.8”

Table Size: 33.10” x 12.60”

ATC: 12 tools

Spindle Taper: #40

Spindle Speeds: 40-4000 RPM

Spindle HP: 7.5 HP

EQUIPPED WITH:

Heidendain TNC-2500 CNC Control

12 Station Tool Changer

Automatic Lubrication

Full Guarding

Coolant System

Misc. Tooling

Specifications:

Lot No: 145

Bar Cap: 2"

Swing: 18-1/8"

Weight: 4000 lbs.

Headstock Oil Reservoir Cap: 31/2 gallons

EQUIPPED WITH:

Twin Disc Clutch

Preselector Head

3-Jaw Chuck

Specifications:

Diameter: 72”

Table: T-Slotted

Rotation: Power Rotation

Notes:

Very Heavy Duty

Specifications:

Diameter: 50”

Table: T-Slotted

Rotation: Power Rotation

Table Capacity: 5000 lbs.

Specifications:

2-Head 24” Width Cap

First Head 6” Diameter Rubber Covered Contact Roll, 20 HP Motor

Second Head 2 ½” Wide Finishing Platen, 15 HP Motor

25” x 60” Abrasive Belts

“Posi-Trak” Electronic Tracking and Pneumatic Tensioning, 15 – 45 FPM

Variable Speed Feed

Equipped With:

Double Infeed and Outfeed Spring Loaded Hold-down Rolls

0” – 8” Maximum Manual Part Thickness Opening with Mechanical Digital Readout

Air Operated Disc Brakes

Motor Load Meters

21” Infeed Conveyor Extension

Infeed Emergency Stop

10" Type K

Table Size:22” x 9”

Spindle Speed:1350 RPM

Motor Speed:1750 RPM

Motor:3 HP

Electrics:220/3/60

Amps:8.4

CAPACITY

Swing: 12”

Collet Capacity: .012-1¼”

Max Grinding Wheel Diameter: 4”

Length of work between spindle and tailstock: 6”

Workhead slide travel:

Longitudinal: 5 ¾”

Cross: 5 ¾”

Workhead Angular Adjustment:

Table Swivel: 325 degrees

Above & Below Center: 40 degrees

Wheelhead Slide Travel:

Longitudinal: 6”

Cross: 7 ½”

Wheelhead Vertical Movement:

Above Center: 4.5”

Below Center: 5”

(3) Wheelhead Spindle Speeds: 4000 RPM; 5729 RPM; 8000 RPM

(1) Workhead Spindle Speed: 436RPM

Specifications:

Type:602-202-8

Wheel Size:12”

Spindle Speed:1800 RPM

Specifications:

RPM: 3400 RPM

Motor: 1/3 HP

Electrics: 115 V/1 PH

Specifications:

Drive Motor: 5 HP

Fan Combination: 16” fan rated 3000 CFM at 4” static pressure

Cartridges: 8- filter with 226 sq. ft. media

Total of 1808 sq. ft. media

More Details:

Chopper and Legs

Square-D combination starter with start/stop push buttons

Fused Disconnect and Fused Internal Transformer for control operation

Reverse Jet Control operation

Control for Manual Sequencing

Patented Exo-Jet Cleaning

Specifications:

Drive Motor: 3 HP

Input Power: 460/3/60

Blower Combination Rating: 3000 CFM at 4” Static pressure, Continuous duty

Filter Configuration: 1- 24” x 24” pleated prefilter

More Details:

Foam Lined Filter

Inlet Panel with 16 Holes

Suspension Bracket

SPECIFICATIONS:

Table: 25” x 26”

Spindle Speeds: 579/3600, 289/1800, 193/1200, 96/600
Gear Drive Head